Welcome to another FREE Woodworking Resource sponsored by your fellow
woodworkers at Shopsmith

Complete the short Request Form at right and we'll send you a FREE Fact Kit which includes a half-hour TV Show, "Sawdust Therapy" that is fun and entertaining to watch.
The Fact Kit explains the amazing story about the famous and affordable MARK V 5-Tools-In-1 Complete Home Woodworking System that packs the five most needed woodworking tools into a single, easy-to-use machine. 
The best part is that if you have space for a bicycle - you have room for a MARK V.

Learn the real story of why over a million folks just like you own a
Shopsmith MARK V.

Doing Jointery on Your Table Saw
Click here for a printer friendly version of Tip-
Pg. 1-3, Pg 4-6, Pg 7-9, Pg 10-12, Pg 13-15,
Pg 16-18,
Pg 19-21, Pg 22-24, Pg 25-27,
Pg 28, Table 3-1

Wood joinery is one of the most rewarding parts of any woodworking project. Ranging from simple, attractive miter and bevel joints to the more complicated lock corner and finger joints, this tip will cover the wood joinery that can be done on the Mark V in the table saw mode.

Miter Cuts

Click to see larger view
Figure 3-1. Some examples of how miter cuts can be used to form four-, six- and eight-sided projects. Click on image to see larger view.

Both miter and bevel cuts are made with the stock held at an angle (other than 90°) to the saw blade. For instance, anytime you change the miter gauge from its normal 90° position, you will be sawing a miter. Some examples of miter cuts used to form four-, six-, and eight-sided figures are illustrated in Figure 3-1. The cut pieces, joined to make forms, are called segments.

It is important to remember that a miter cut angle is always one-half of the joint angle. The joint angle in a four-sided picture frame is 90°, but the cut angle is 45°. Use the following formula to determine the correct miter gauge setting for a project with any number of segments: Divide 360° by the number of sides and then divide the answer by 2. To apply this formula to an octagon, for example, divide 360° by 8; then divide the answer, 45°, by 2. This will yield 22-1/2°, which would be the correct setting for the miter gauge.

To make any miter cut, set the miter gauge at the desired angle, and secure the lock knob. Warning: Place the miter gauge in one of the slots so that the face of the gauge is angled toward the blade. If you mount the miter gauge so the face is angled away from the blade, the wood may bind and kickback. Note: Since most miter cuts are made at 45°, the miter gauge has positive stops to help you quickly adjust the gauge to 45° left or 45° right. However, it's wise to check critical setups with a drafting triangle or combination square.

Mark the workpiece where you want to cut it. (It's best to measure from the inside corners of the miter.) Align the workpiece with the saw blade and clamp it securely with the miter gauge safety grip.

Click to see larger view
Figure 3-2. To make a miter cut, set the miter gauge at the desired angle, then proceed as if you were crosscutting.

From this point on, the procedure is similar to crosscutting. Make a five-point check. All five locks-power plant, carriage, table height, table tilt, and quill-should be secure. Turn the machine on, set the proper speed and let the machine come up to speed. Push the workpiece slowly past the blade (Figure 3-2). When the cut is finished, turn the machine off and let the blade come to a complete stop before removing the workpiece or scraps.






Click to see larger view
Figure 3-3. A fence extension that is faced with sandpaper provides a high friction surface that helps to keep the workpiece in place as you are sawing.

Miter sawing is no more difficult than straight crosscutting but accuracy is most critical. An error of 1° doesn't sound like much, but when it's repeated on even just four parts, it adds up to frustration at assembly time. Make it a habit to test machine settings on scrap stock. Saw the good material only when you are sure the setting is perfect. Guard against drift which is the tendency of the blade's rotation to pull the workpiece-perhaps just enough to spoil a perfect cut. A fence extension that is faced with sandpaper helps keep the workpiece in place (Figure 3-3). Hold the workpiece securely; use the miter gauge safety grip.

Here are some things that will cause inaccurate miter joints:

  • Improper alignment of the machine.
  • Dull saw blade or incorrectly set teeth.
  • Stock warped or otherwise imperfect to begin with.
  • Stock allowed to drift.
  • Pass made too fast.

Mitered segments must be perfectly matched in size and shape if they are to join together in a perfect union. Use this formula to determine the segment length:

Frame width - rabbet width x 2 + picture length = frame length

Example for 8" long picture:

2" - 3/8" = 1-5/8" x 2 = 3-1/4" + 8 = 11-1/4"

Click to see larger view
Figure 3-4. The miter gauge stop rod can be used to gauge the length of the segments.

The miter gauge stop rod can be used as shown in Figure 3-4 to gauge the length of the segments. Square a piece of stock to this length. Set the miter gauge to the angle needed, and miter both ends of the segment. Then use it to set the miter gauge stop rod. Warning: Never position the miter gauge stop rod so that it crosses in front of the blade. Other segments are cut from one length of stock by mitering it at one end, then holding the mitered end against the stop rod. Be sure that you turn the stock over for each new pass.


Click to see larger view

Figure 3-5. (A) A miter gauge extension with an adjustable stop can be used to cut mters on wide stock. (B) Construcion details of the miter gauge extension. Click on image to see larger view.

A miter gauge extension with an adjustable stop can be used to cut miters on wide stock (Figure 3-5).

Miter Cuts with a Fixture
Cutting close, tight miters is much easier when you use a sliding table fixture (Figure 3-6). The fixture is easy to make and is well worth your time and effort, because a fixture that is well built and set up accurately will enable you to cut perfect 45° miters every time. The strips that slide in the miter gauge slots are cut to fit from hardwood. Use screws to secure the strips to the base; then cut a 12" long saw kerf into the fixture.






Click to see larger view

Figure 3-6. (A) The sliding table fixture can be used to make close, accurate miters with ease. (B) Construction details of the sliding table fixture. Click on image to see larger view.

Miter one end of each hardwood fence at 45°. Use glue and screws to secure one of the fences into place at 45° to the saw kerf. Once the glue on this fence has dried, use an accurate square to position the other one; secure it with glue and screws. So that the stock will have less tendency to drift while being cut, attach fine grit sandpaper onto the fixture with rubber cement.

When using this fixture, always cut matching miters. This is done by cutting the first corner of the stock on the right side of the fixture and the second corner on the left side.

Remember that all fixtures, in addition to being carefully made, should be protected so they will maintain accuracy. Carefully sand all parts before assembly. Use glue and screws to join components. After assembly, apply several coats of penetrating sealer with a light sanding between coats and another light sanding when the final coat is dry. Wax and buff those surfaces that make contact with the machine.

Continue to Bevel Cuts


Send For Your FREE Woodworking Fact Kit and "Sawdust Therapy" TV Show.

First Name*:
Last Name*:
Street Address*:

USA Canada

E-mail Address*:

  2009 Shopsmith Inc. All rights reserved.

Policies | Contact Us | Links | Corporate Web Site